Despite the durability of Nutribullet blenders, there can be times when they act up or behave like we are experiencing an alien invasion. Some owners have often asked, “why is my Nutribullet blinking?”
Why is my Nutribullet blinking? The reason is quite simple; it is due to overheating. Anytime you notice your Nutribullet is blender is blinking away instead of functioning as it should, simply unplug it from the power socket and allow it cool for a couple of minutes – let’s say 15 minutes – before plugging it back to the power source.
Overheating is likely to occur if you are using the blender for a long amount of time or the environment it is working in is above normal temperature.
To prevent future occurrences, ensure your blending environment is properly ventilated – and if you have a lot of ingredients to blend – try blending in batches to give your Nutribullet blender ample time to rest.
Why has my Nutribullet suddenly stopped working?
Contents
Aside from the blinking lights, there could be other times when your Nutribullet suddenly stops working. This can be due to one or some of the following reasons as explained below;
1. The plug could have been accidentally unplugged
A Nutribullet plug can be accidentally unplugged if you overstretch the reach as a result of the cord being short. It could also be that your pet or a toddler accidentally trips the cable thereby causing a sudden disconnection.
2. Too many ingredients in the Nutribullet container
If the lights are on but the blade refuses to grind, it could be as a result of you filling up the Nutribullet container without allowing the blades enough space to spin. Too many ingredients can jam the blades, especially if the ingredients are dry.
Even if the ingredients are fresh, endeavor to only fill up the container halfway and add a little bit of water to allow the ingredients to swirl easily. For dry ingredients, you might have to put them little by little for the best result.
3. Dull blades
There are times you feel you aren’t getting the right texture from your Nutribullet blender; it could be a result of dull blades. The blades of any blender can get blunt over time as a result of excessive use, and the only way to get it back to its previous glory would be to sharpen the blades. I will run you through this process in the subsequent section of this article. Keep reading!
4. The Nutribullet doesn’t power on
If your Nutribullet doesn’t power on, it could be that the cup tab is broken or the blender cord is bad. Also, don’t eliminate the possibility of the cord being unplugged so do well to check.
5. The blade motor stops working
if your Nutribullet blender suddenly stops working on its own accord, and even when you give it time to rest it still wouldn’t come on, then it could be that the blade motor has gone bad. When you run your Nutribullet for too long, you stand the chance of burning the motor. Generally, blender motors are to be used at 1-minute increments, anything less would place the blade motor at a very high risk of damage.
Read also- What Is The Black Stuff From My Nutribullet Blender?
How to sharpen the blade of a blender
Before thinking of changing your Nutribullet blender due to blunt blades that no longer chop as they do, you should consider sharpening them yourself to bring them back to life. Below are what you need to get started.
- Hand gloves
- Sharpening stone
- Scouring pad
- Warm soapy water
Step 1
Switch off the blender from the wall
Before doing anything else, switch off the blender from the all to eliminate every chance of the blender switching on by itself during the process. Don’t just switch it from the wall; completely unplug it from the wall socket, then remove the Nutribullet container from the motor engine.
Step 2
Clean the container – have a clean working environment
You generally need to work with clean parts in a clean and clear working environment, so before you proceed, eliminate any old food particles and dirt in the blender container. Put it inside a sink or bowl loaded up with warm soapy water, and utilize a scrub pad or wipe cushion to thoroughly wash it.
Give particular attention to the tight little hiding spots at the base of the blender and use a bottle brush in such areas if you are certain the sponge won’t do the job. Washing your Nutribullet jar in warm water will likewise assist with making it easy to remove the seal that holds off the blade in the container.
Ensure you completely dry the seal with a soft towel or cloth when you are done – handling it roughly can cause your blender to leak.
Step 3
Carefully remove the blade
At the base, you will see where the sharp blades are housed. Bend it counterclockwise to separate it from each other; it should freely come off with very little resistance – ensure you wear your rubber gloves when doing this to avoid any sort of injury. Then, place the container on the counter for safety purposes.
In your grasp, you should now have a ring or seal, the base, and the sharp Nutribullet blender blades. Separate these parts from the base, and put everything down close to the container, except the blades – remember to hold it carefully.
Read also-Why Is My Blendjet Blinking Red?
Step 4
Wash the blades carefully
Hold your Nutribullet blade in the warm bowl or sink of soapy water – do not let go at any moment. This is because the lather formed by the soap can make it difficult to see the blades in the water, which means you may need to stretch around indiscriminately until you can feel it.
Note that, even a dull Nutribullet blender blade can injure you if you don’t throw caution into the wind. Endeavor to wear your rubber gloves all through this process, as this gives at minimum some security to your skin.
Wash the Nutribullet blades completely, and clean away any hardened substance or extra food particles using a scouring pad to get the best result. Once done, allow to dry before proceeding to the next step.
Read also- Can You Take A Nutribullet On A Plane?
Step 5
Sharpen your Nutribullet blades using the sharpening stone
Start by moving one of the Nutribullet blades on the sharpening stone, ensure you stick with the already sharpened side of the blade – sharpening the blunt side will only be a total waste of your time.
Additionally, keep a reasonable distance from the sharpening stone as you continuously file the blades to prevent any mishap from happening. After filing one part of the blade long enough, turn over to the other side and repeat the procedure.
The blades will have four sides (two fronts and two backs) that need to be sharpened, and every Nutribullet blender normally has two to four sharp edges, depending upon the model. Continue the process until each edge has been sharpened for a reasonable amount of time.
Step 6
Assemble your Nutribullet blender
Once you are certain you have done a good job, clean the sharp blade with a wet rag and dry them in a clean towel or moisture absorbing cloth. While still wearing your hand glove, return the blade to where you removed them from and add the seal you removed earlier and screw back anything that needs to be screwed.
Ensure the container’s base is correctly fixed and in one piece before you plug it into a power source to test how good a job you did.
NB: there’s a high chance you might want to test the sharpness of the blade by running it on your thumb – don’t be that naïve. If the blunt blade can injure you, imagine what a sharp blade would do. You can use fruit and try slicing it across the sharp edges, or better still, couple everything back and do it the right way as explained above.
FAQS
How do I reset my Nutribullet?
You know your Nutribullet needs to be reset once the blade stops turning or you notice a burning smell. To reset, simply unplug your Nutribullet from the power source and allow it cool for at least 45mintues-1 hour. The power base of a Nutri bullet blender automatically resets when you unplug it from its power source.
Read also- Can A Magic Bullet Blend Ice? Find Out
How long will a Nutribullet last?
Every Nutribullet I have come across has a 1-year warranty. Regardless of the warranty, your Nutribullet is designed to last for at least 4-years, provided you have very good maintenance culture.
Can the Nutribullet overheat?
Yes, Nutribullet blenders can overheat. Do not be alarmed though, they are designed with circuit breakers that automatically trip off the motor when it overheats. The moment this happens, your blender will suddenly turn off – do not switch it back on immediately as you could damage it beyond repair. Allow it cool for at least 45 minutes to 1 hour before turning it on.
Conclusion – why is my Nutribullet blinking?
Having known how to troubleshoot your Nutribullet blender if any of the issues stated in this article arises, do well to maintain your blender and ensure they are in good shape before using them. kindly drop your comment and suggestions in the comment section. Cheers…
