How To Get Water Out Of An Immersion Blender In 2021

This post contains affiliate links. Read the full disclosure here.

If there is any challenge faced with immersion blender asides from splattering food about when not handled properly, then it’s get rid of that annoying water sound from the attachment.

Many immersion blender owners have ended up ruining their immersion blenders because they just had enough – well, I ruined two myself till I discovered this trick I am about sharing with you shortly on an online forum.

Do note that it comes with its own risk, but if you’re able to manage it carefully, then you won’t be having any problems at all. Here we go!

Pro Steps To Getting Water Out Of An Immersion Blender

Requirement:

Step 1: Unplug the immersion blender from the power source

You must unplug your immersion blender from the power source before taking any step I will be outlining in this article – you wouldn’t want to risk any form of electrical outrage no matter how little. Don’t just switch off the plug, unplug it completely.

Step 2: Plug your oven into a power source

While you have to unplug the immersion blender from a power source, the reverse should be the case for your oven.

Plug your oven into a stable power source that works without any form of interruption. You’ll need the power source to be stable throughout the entire process to get the best result.

Step 3: Set the oven to low heat

After plugging in the oven, set it to low heat (50 degrees Celsius) and place the attachment in it. This is where the “watchful eye” I spoke of earlier comes into play – as the water is being heated at that temperature in the oven, you will clearly see the water droplets dropping on the tray as the water within begins to expand – and as they drop on the tray, the same temperature licks it up.

Step 4: Repeat the process

Do not leave it until all the water droplets exit the attachment as it might not go well with the material composition specially if it is made of plastic.

Step 5

Remove it every two to three minutes, allow it to cool, then put it back in – repeat this cycle until there is no annoying sound giggling in your immersion blender.

You should however note that this may not sit well with the manufacturer of the product, and you also ensure to keep a watchful eye on the happenings inside the oven.

Do not for any reason leave the attachment inside the oven and go about other activities – you could have an explosion in your hands by the time you return.

An oven with a transparent door is the most suitable for this exercise. It worked for me, and I know it will work for you too.

Here are other tips you can follow to enjoy your immersion blender to its maximum capacity.

Trending Searches:

FAQ- How To Get Water Out Of An Immersion Blender

 

How Do You Keep An Immersion Blender From Splattering?

One of the major problems I had with immersion blenders, apart from the water storing away in the attachment, was when I had to clean my entire kitchen because of a splatter I caused due to not being duly informed of the workflow immersion blenders follow.

Below are tips you can use to avoid the unnecessary stress I had to go through, especially if you are using an immersion blender for the first time.

Tip 1- Never Blend In A Wide / Flat Bowl

One of the mistakes I did during my first try was using a large bowl. No matter what you intended blending, the items should be put in a narrow bowl, not too narrow per se, but just something that has side covers like Norpro Silicone Measuring Stir and Pour Or Liberty Stainless Steel Malt and Milkshakes Ice Cream Mixer Mixing Cup.

The wider the container, the more likely it is to have your food splattering all over the place.

Tip 2. Use The Correct Hand Movement And Angle

It doesn’t matter if you are left-handed, right-handed, or even ambidextrous; the fact remains that a single motion mistake while using the immersion blender will simply cause all your food items to splatter everywhere.

Just in case you are wondering what I mean by a single motion mistake – do not attempt rotating your immersion blender on your own, or make a horizontal movement.

In other words, no horizontal and rotational movement while blending the food items. Simply hold your immersion blender tightly and do a vertical movement (taking your hands up and down) to get a better result.

Tip 3-Do Not Bring The Rotary Blades Too Close To The Surface

Bringing the rotary blades too close to the surface could also cause a splatter. The rotating effect as you move your hands vertically will cause the food above to flow to the bottom. Also, avoid taking it too close to the bottom.

If the bowl is spacious enough, try slanting the immersion blander to a 60-degree stance for it to mix up properly – this is effective when blending your soup.

Tip 4- Use A Deep Bowl

The depth of the bowl matters when it comes to curbing problem of spattering. So, in all your bowl choices, avoid using small bowls or shallow bowls. Just like I earlier stated. While using wide bowls are not ideal, using shallow bowls are also not recommended. Deep bowls will do a perfect job and also give you the perfect protection.

Tip 5-Control The Blending Speed

The faster the blending speed, the smoother the outcome you should expect, and vice-versa. I also recommend starting at a lower speed to a higher speed to have a uniform blend – this is because starting at a very fast rate is likely to cause your food to have lumps, except that’s how you want the food to turn out.

Tip 6-Immerse Before Initiation

One other mistake I can remember making was turning on my immersion blender before immersing it in the soup I wanted blending, and the result?

Well, I guess you know by now. Fully immerse your immersion blender before turning it on, and set the blending speed based on how smooth or coarse you want your mix to be.

Tip 7-Make A Paper Barricade

Splattering can be avoided with an artificial barricade. Maybe for some reasons you still feel rather unsatisfied with the results you are getting with regards to having splashes

Simply get a large chunk of cardboard paper and create a sort of wall by making a cylindrical structure your bowl can easily fit into without any problem – the cylindrical structure now acts as a shield in case the food starts flying around.

Read also- Can I sharpen immersion blender blades? 

How To Clean An Immersion Blender

I personally think one of the reasons why people go for immersion blenders is the ease with which one can clean them. However, if you still find it challenging, here are the steps you can use to effectively clean your immersion blender.

Step 1- Remove The Attachment( If it’s Detachable)

As a rule, the simplest method to clean your immersion blender is to take out the attachment and clean it independently using a normal dish cleanser and water.

Press the button that removes the attachment from the blender, take it off, and soak it in hot water and cleanser for some minutes, to slacken any food particles that might be attached to it. Wipe it clean with a dishcloth to make it dry.

Step 2- Turn/ Blend With Soapy Water

If You notice some amount of dried food particles on the blades attachment, fill a little bowl with heated water and put a drop or two of dish cleanser. Lower the blender in the water and set it to the ‘On’ position.

Mix the foamy water composition until the food is taken out of the attachment. Turn the blender off and remove the connection by pressing the button based on your hand blender model. This simple step is very effective in taken stuck food particles from the immersion blender.

Step 3- Leave The Attachment To Dry

Once you are certain the attachment is clean, put it on a dry drying towel or drying rack and leave it to dry before storing it. This step is important, as it helps reduce the possibility of having water in the compartment. What I personally do at times is to take the compartment outdoors and dry it under the sun, the heat of the sun will most certainly suck up any water left in the compartment.

Step 4- Clean Up The Wand/ Power Section

In all your clean, do not soak the wand/ control section in water, or leave under a running tap as you did with the attachment, as this is the main component of your immersion blender – except you have no use for the blender of course.

Simply use a damp cloth to clean the wand after you most have wiped down the food particles from it – that should do the job.

Step 5- Store Your Hand Blender

Store your hand blender in a location that will keep it liberated from dust, yet, the location should be anything but difficult to reach so that you can utilize it effectively at whatever point required. Be certain that the hand blender’s parts are largely totally dry before putting it away.

By following these basic advances, you will have the option to clean your blender and make them work at the top of their game for quite a long time to come.

Make certain to clean the blender immediately after its utilization to make the cleaning cycle significantly easy.

Can Immersion Blenders Go In A Dishwasher?

To play it safe, ensure to check the manufacturer’s label or instruction to see if the blender attachment is dishwasher safe. If the attachment is dishwasher safe, put it at the top rack of the dishwasher for an effective result, but if it isn’t, simply follow the step I outlined in the segment above for a good result.

You should however note that washing your hand blender’s attachment in a dishwasher will definitely increase the possibility of water entering the compartment, which is something we should all try to avoid altogether.

Only the attachment should be considered for the dishwasher – not the motor, the chord, or any other part for that matter.

How To Repair An Immersion Blender

Before rushing to the technician or trashing your immersion blender, try troubleshooting using the following guidelines I will be outlining below;

Phase 1. Ensure The Switch Is Working

The most widely recognized hand blender issues will be issues concerning their switch. If you attempt to turn on your blender and it isn’t working, you may have to check it by using a volt-ohm meter.

Join the plug prongs of your immersion blender to the volt-ohm meter, by setting the meter on the scale – It should normally have a low resistance result displayed; notwithstanding, if the reading displayed is infinity, then the possibility of something being wrong with your power switch is very high.

Phase 2. Open Up The Motor For Cleaning

Open the motor body by using the right screwdriver, and cautiously check the unit, especially the switch area. Clean the contacts of the switch. Be certain that the openings of the body and the terminals situated at the back segment of the switch block are cleaned as well.

In many cases, cleaning these areas will consequently take care of the issue, yet if it doesn’t work, then you should consider changing the switch.

Phase 3. Have A Look At The Blade Shaft

When the blade shaft gets stuck, which can happen due to the food you are trying to blend, dismantle your immersion blender until you can access it. The reason for the jam is normally food and debris that are being logged up over time. Clear out anything you see, and afterwards, use a lubricant. Preferably this oil to grease up these areas.

Phase 4. Check The Fuse Section

If you feel you are up to it, dismantle the unit further to check the fuse situated in the inward part of the hand blender’s motor. You can check this by removing the wire connector connecting the lead box that contains the wire and the power cord of your blender.

Clasp the volt-ohm meter tests on the two closures of the lead box, and set it to the RX1 scale. You ought to have a low reading value, but if the reading is high, it implies that you need to replace the fuse before it causes a greater problem.

Ensure you take the old fuse with you when going to buy another one so you can be certain your substitution will fit.

How To Get Water Out Of An Immersion Blender-Conclusion

For those of us who love to have gadgets and appliances that are easy to use and move about, immersion blenders are the way to go.

Although they have their limitations compared to the normal blenders we have come to know, we can all agree on one thing, and that is the simplicity with which immersion blenders can be used and maintained.

Leave a Reply