How To Fix A Leaking KitchenAid Blender With Steps

What Can Cause A KitchenAid Blender To Leak? For some of us, one of the problems we are bound to encounter with our blender is when the container starts leaking on its own. Sometimes, it happens so suddenly without any external contact, and you begin to wonder what went wrong.

Well, three things can cause your KitchenAid blender to leak, and here they are;

  • Loosed ring assembly
  • Slacked seal
  • Faulty blade assembly

Before giving up on your blender, it’s almost certain that one of these three problems is responsible for the leakage – so follow the steps I will be outlining below to get your pitcher back in order.

Pro Steps To Fixing A Leaking KitchenAid Blender


Step 1- Remove The Pitcher From The Motor

The first thing you should do is to dismantle the pitcher from the motor since that’s where the problem is – removing the pitcher from the motor also gives you a closer look at where the leakage might be occurring.

Step 2- Turn The Pitcher Upsidedown

After dismantling the pitcher from the motor, turn it upside down, then tighten the ring underneath – the ring assembly can be loosed due to wear and tear or constant removal of the pitcher from the motor assembly.

Whatever the reason, tighten the ring assembly, but don’t apply too much force so that you don’t break the rubber component in the process which can ruin everything.

Trying pouring water into the component after tightening the ring assembly – if the leak still continues, pour out the water and dry up the pitcher with a towel, then proceed to the next step below.

Step 3- Take Off The Ring Assembly

Once you confirm that the pitcher still leaks after putting water from the step above, unscrew the ring you just tightened, to take off the ring assembly. After taking the ring off, the whole assembly will come out. Be careful so you don’t drop the ring on the floor.

The removal of the ring will allow you check if the seal is broken or slacked – to confirm this, look out for cracks on the seal – if you see cracks, then the reason your blender leaks is because of a loosed seal, and the only way to fix a cracked seal is to replace it.

However, if your seal is in perfect condition, then follow the step below for the final remedy.

Step 4- Get A New Blade Assembly

The final remedy will be to get a new blade assembly for your KitchenAid blender. Note that getting a new blade assembly for your KitchenAid blender will require you to also get a new seal.

Once you purchase a new blade assembly put the new seal in the required position – ensure the seal is wet so that it gets a good grip on its sitting position.

Put the new blade assembly after sitting the seal, then tighten the ring as firmly as possible.
This should stop every form of leakage that had occurred in the past – to confirm, put water into your now assembled pitcher and attach it to the motor, blend at the highest speed and note the change.

The necessary parts required to get your blender back in shape are relatively cheap, compared to getting a new blender.

Read also- Can a food processor overheat?

Why Is My KitchenAid Blender Leaking From The Bottom?

Just as I stated at the beginning of this article, the reason your KitchenAid blender will leak is because of the following;

Slacked And Worn Out Seals

The most common causes of leaking blenders are slacked seals, and this can occur in two ways; when they are worn out, and when they are installed incorrectly (upside down) by the manufacturers.

There have been few cases where blenders start leaking from the moment you start using it for the first time – this is actually a manufacturer flaw, as the possible explanation of this is when the upside-down instalment of the seal on the gasket.

Don’t be in a haste to return a blender, whether KitchenAid or any product for that matter – Simply lose the ring and properly sit the seal in the right manner, and you are good to go!

Loosed Ring

Another common factor is when the ring is not properly tightened to the pitcher – This can be likened to a running tap in your kitchen sink, if you don’t tighten the control properly, you are likely to have water trickling from the tap outlet.

To prevent this scenario with your blender, always tighten the ring before using it, especially if you often remove it from the motor for storage purpose – and while at it, ensure you take care not to destroy the plastic by using excessive force.

Once you ascertain the ring can’t go any further when tightening, simply stop so as not to cause damage.

Faulty Blade Assembly

Another cause of leakage is usually a faulty blade assembly, but this is usually the least occurring amongst the three I outlined in the first segment of this article – and when such happens, you can try dismantling the blade section to do a proper cleanup of the blade assembly, and if it still leaks, change the entire blade assembly.

Below Are Further FAQs You Might Have Regarding Blenders

Do All Blenders Leak?

Eventually, all blenders will leak no matter the amount they cost. What really matters is how much you use them. There will always be room for wear and tear.

How Do You Take Apart A KitchenAid Blender?

Certain times require to apart your KitchenAid blender, which could include storage reasons or times when you have to travel with your blender, or completely change location. Below are the steps to follow when dismantling your blender for such purposes;

Step 1- Turn Off The Blender

Of course, I know you have to definitely turn off the blender before packing it, but it’s important to remind you anyway. Remember to turn off the blender, and also unplug it from the power source.

Step 2- Remove The Pitcher

To remove the pitcher, simply have a firm hold on the handle, then pull it up from the base. Ensure not to use excessive force to avoid any sort of mishaps that are bound to happen from such actions. Removing the pitcher also helps you create space in the storage mechanism.

Step 3- Remove The Lid

The next thing to do is to remove the lid from the pitcher/container. Removing the lead will give you space to keep smaller pitchers, that’s if you have any.

Do not attempt to remove the ring or the blade assembly as you have just found out, a lot of things can go wrong in the process of doing such.

These simple and easy steps should take apart your KitchenAid within a minute or two. Simply follow the same process if you want to reassemble the blender.

How Do I Fix A Blender That Is Not Spinning?

It’s quite sad that most blender owners don’t give their blender a second chance, especially when it comes cheap – they simply dispose off it anytime there happens to be a minor issue arising.

Anyway, if your blender happens not to spin anytime you power it on, below is how you can go about it.

Step 1- Check The power Source

Check the power connections and connectors if your blender is not working. This can be checked by removing the power cord, and afterward, test the electrical switch by turning on the blender from the blender’s switch.

Use a multimeter and press the blender’s switches one after another. If there is a low reading, then there are no problems with the switch.

However, if the readings you get are proportionally high, then it means the blender’s switch is responsible for it not turning as expected.

Step 2- Cleanup The Terminals

Something else you can do to fix a blender that isn’t spinning is to clean the terminals. First, pull out the plastic faceplate which covers the casing and button switches to uncover the screws holding the switch casing cover – then unscrew the screws which append the plate to the lodging by using a screwdriver.

To clean, spray solvent on the openings and terminals. This also may work and may fix your blender spinning problem.

Step 3- Test The Fuse

You can also check or test the wire. First, discover the breaker which is toward the wire end that comes from the terminal to which the power cord is appended.

Use a voltmeter to check the reading – if the reading is high, then it means your blender is not spinning as a result of the dead fuse, but if the reading is low, then your fuse is okay.

Step 4- Clean The Blender Blades

Another conceivable reason for the blender, not spinning could be food particles jamming the blades. For this, you should initially dismantle the drive and then turn the blade shaft.

If you turn the blade and you confirm that it is stuck, try looking out for stuck food particles that are likely to cause it. If it is something you can remove, do so carefully so that you don’t injure yourself in the process, otherwise, you can just change the entire blade assembly.

The next step to take after carrying out the above step is to give the blender a last check, which will require you to plug the blender in and press the switches.

The blender should be spinning by now, and the lone reason why it wouldn’t spin after carrying out all the steps listed above would be if the motor has an internal problem you aren’t aware of.

For this situation, you may need to get the motor changed, or better still, by a new blender.
Blenders not spinning is a typical issue and is generally caused by one of the abovementioned. Nonetheless, if you can’t comprehend or fix the issue, you should go after expert’s assistance.

How Do I Fix My KitchenAid Blender That Is Not Spinning?

If you have a KitchenAid blender that’s not spinning, then before going through all the steps I listed above, try following the steps I will list below;

Materials Needed

  • A new coupler
  • A punch
  • A hammer

Step 1- Turn Off The Blender

The first thing you should do is to turn off the blender – this will ensure that the motor is not powered while you carry out the necessary work on it.

Step 2- Remove The Pitcher From The Motor And Notice The Change On The Coupler

The next step is to remove the pitcher from the motor, and have a closer look at your coupler – you will notice that the teeth of your coupler have been severed to the point where it no longer has any sharp teeth with which to run the blades.

This is usually caused by not properly adjusting your KitchenAid blender to sit on the motor before turning on the switch, and as such, the coupler’s teeth will continue to spin on the metal underneath which will cause it to give way eventually.

To avoid this in the future, ensure there are no gaps between the pitcher and the motor, make sure it laps properly on the motor before turning on the switch. Don’t be in a hurry!

Step 3- Get A New Coupler To Change The Old One

Once you confirm that the teeth of your KitchenAid blender coupler are bad, get a new one on amazon by clicking here – this coupler is very durable, and it will serve you for a very long time as long as you use it properly.

Step 4- Remove The Worn-out Coupler

This is where your punch and your hammer comes in – place your punch and place it on the worn-out coupler on the motor, ensure the punch is placed facing the clockwise position of the rotary object since it is known to rotate anticlockwise.

Then use your hammer to hit the punch with a reasonable amount of force – this will remove the worn out coupler from the motor.

Step 5- Replace It With The New Coupler

Get your new coupler and simply screw it in the position where the old coupler was – you don’t have to screw it all the way in, just enough to fit into the motor, and when you later turn on the blender for testing, the coupler will screw itself properly.

Step 6- Properly Place The Pitcher On The Motor

Once you finish installing the new coupler, properly install the pitcher on the motor, and ensure it fits perfectly on it. when you turn it on, you can be certain that your KitchenAid blender will spin.

How To Fix A Leaking KitchenAid Blender- With Steps- Conclusion

Don’t be in a haste to trash your blender. Always take out time to see if you can do certain things on your own without any external help – not only will it help you build your motor skills, it will also help you save a friend who might also want to trash out their blenders. Knowledge is generational, and “doing it yourself” is a good way to start. Cheers!!!

Leave a Reply